How to Install a Bathtub
How to Install a Bathtub
Blog Article
We have uncovered this post on How to Install a Bathtub down the page on the web and believe it made sense to write about it with you on this page.
Setting up a bathtub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately difficult job. If the old tub is conveniently available, the job can move rapidly; if you need to open a wall surface to remove the old bathtub and place the new bath tub, the task is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. Make certain you have qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is far better to think about using one before you begin. Chances are you might need a specialist plumber to make tube connections.
This post will certainly assist you install a new tub in your bathroom if you have actually currently purchased a brand-new tub as well as do not need to alter the setup of your previous supply of water pipes.
Your devices and also material checklist need to consist of the following:
Getting ready for the Installation
First of all, the sustaining structure provided with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is separate the water. After doing so, activate the faucets to drain any water staying in the system. The process of getting rid of the existing faucets can be rather bothersome as a result of the limited gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will certainly originate from the pipelines. When the supply pipes have actually been gotten rid of, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, position the tub in the required placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub until the level checks out degree.
To set up faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks and also tighten them if required. Fill up the bathtub and additionally check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bath tub should wait up until the tub has actually been used at least once as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in area in between the faucet and the sink. Secure the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to enable the motion experienced when the tub remains in use. The sealer can break relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is a good idea to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our post about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking time to read through our article post. Are you aware of anybody else who is occupied with the subject? Please feel free to share it. Kudos for your time. Visit us again soon.
Request Free Estimate Report this page